Carpet cleaner rental. Rent the best for $21.99 / 24 hours

Wekiva True Value, Longwood. Carpet and upholstery cleaner rental

Instructions

Thank you for your interest in our carpet cleaner and upholstery cleaner rental. Here are the directions to make your carpet cleaner rental successful. 

Used as directed, our cleaning system is safe for all carpets that will not shrink or fade.

Before cleaning, always test a small hidden patch for shrinkage and color fastness. DO NOT over wet carpet. Excessive soils may require a second cleaning.

Preparation

Preparing your carpets or upholstery is always an important first step for professional results. Remove furniture, protect furniture not being removed by placing foil or plastic under furniture legs. Vacuum areas you intend to clean thoroughly. You may find it necessary to pre-treat heavy traffic areas and stains prior to cleaning by using the Carpet and Upholstery Pre-spotter. Follows directions on the bottle.

Assembling the unit

Here are the directions to make your carpet cleaner rental successful. Used as directed, our cleaning system is safe for all carpets that will not shrink or fade.

Before cleaning, always test a small hidden patch for shrinkage and color fastness. DO NOT over wet carpet. Excessive soils may require a second cleaning.

Filling the tanks

Do not remove the solution lid because of the heating element inside. Mix solution of Carpet and Upholstery Cleaner using hot water, per directions on the bottle. Fill solution tank. Use the Deorderizer as directed to eliminate odors. Use of Deformer is required! Remove plastic dome and add Defoamer as directed on the bottle. If you have ever cleaned or used spotters to remove stains, this is a must to prevent recovery tank from foaming over onto your carpet as you clean. DO NOT try to remove the cover from the solution tank. It is permanently attached for safety reasons. Removal will damage the unit and you will not be able to get your deposit refunded.

Cleaning with the system

Position machine to clean a 3 to 4 foot section. Begin by squeezing the trigger on the cleaning wand and moving the wand in a forward motion to release the cleaning solution onto your carpet. Release the trigger to stop the cleaning solution from dispensing and pull the wand back toward you with light pressure downward. If you are using the powerhead, no pressure is needed. The brush does all the work. This will vacuum the solution and dirt out of the carpet, dispensing it into the recovery tank. Use slow overlapping strokes on each pass for consistent cleaqning. Continue the above steps until dispensing nozzle at the tip makes a sputtering noise. This tells you the solution tank is empty. Turn off all switches, empty the recovery tank of dirty water and refill solution tank as directed above. Once unit is refilled, continue cleaning.

Protectant and Drying Time

To keep the carpets clean for a longer period, spray carpet with Carpet Protectant while carpet is still damp. This will ensure and even coat of Protectant.


Try to avoid walking on damp areas if possible. Total drying time will vary due to conditions such as humidity, temperature and room ventilation, Usually, the time required is 3 to 4 hours.

After you're done

Please follow the directions below to clean the Unit and Powerhead. A $10.00 cleaning fee will be charged on each if the Unit and Powerhead are not returned in the same condition as when you picked it up.

How to clean the Carpet Cleaner

1. Turn pump switch "off" when finished cleaning. Leave vacuum switch "on" and disconnect vacuum hose from cleaning wand and insert it into the solution tank to remove and left over cleaning solution.

2. Turn vacuum switch "off" and disconnect the wand. Holding the wand over the recovery tank, trigger the valve so that excess solution in the hose can drain into the recovery tank.

3. Empty recover tank. Rinse and dry tank inside and out.

4. Rinse and dry all hoses. Hank vacuum hose up to let water drain from inside.

5. Clean entire machine with a damp cloth and mild all-purpose cleaner and wipe dry. Replace recovery tank and store vacuum hos inside.

How to clean Powerhead and Brushes

1. Never spray water on or under the Powerhead. Wipe Powerhead and cord with a damp cloth and mild all-purpose cleaner, top and bottom.

2. Remove all lint and hair from brushes by using a stiff brush. Wipe bottom clean with a damp cloth.